PICkit4が届いた [PICkit4]
(2018.08.17)
秋月電子に注文したPICkit4(↓)が届きました。これで開発作業を再開できます。
http://ec.akizukidenshi.com/catalog/g/gM-13337/
先ずは、こちら(↓)のサイトを参考にして壊れたPICkit3にFirmwareを書き込んでみました。
http://koibo.blog.fc2.com/blog-entry-40.html
PICkit4はPIC24FJ256GB106も(未だ殆どのデバイスが)βサポートなのですがMPLAB-X IDEで接続して、書き込むことが出来ました。
*****************************************************
Connecting to MPLAB PICkit 4...
Currently loaded versions:
Application version............00.02.00
Boot version...................01.00.00
Script version.................00.02.52
Script build number............66d22ca77a
Application build number.......0123456789
Connecting to MPLAB PICkit 4...
Currently loaded versions:
Boot version...................01.00.00
Updating firmware application...
Connecting to MPLAB PICkit 4...
Currently loaded versions:
Application version............00.03.09
Boot version...................01.00.00
Script version.................00.02.52
Script build number............66d22ca77a
Application build number.......0123456789
PICkit 4 is supplying power to the target (3.25 volts).
Target device PIC24FJ256GB106 found.
Device Id Revision = 0x3
Erasing...
The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x2ff
program memory: start address = 0x800, end address = 0x7fff
program memory: start address = 0xec00, end address = 0xedff
program memory: start address = 0xf000, end address = 0xf2ff
program memory: start address = 0xf800, end address = 0xf8ff
program memory: start address = 0x10000, end address = 0x15bff
program memory: start address = 0x29f00, end address = 0x29fff
configuration memory
Programming/Verify complete
*****************************************************
PICkit3のUSBケーブルを接続し直すとStatusの赤色LEDが消えて、直ったように見えたのですが・・・
Connection failed から抜け出すことは出来ませんでした。orz
もう一台のPICkit3にFirmwareを書き込む準備が出来たら、再挑戦します。
ーーーーーーーーーーーーーーーーーーーーーーー
<おまけの報告>
PICkit4はPIC16F1829もβサポートですがプログラムを書き込んでデバッグすることが出来ました。
(実はかなり使える?)
秋月電子に注文したPICkit4(↓)が届きました。これで開発作業を再開できます。
http://ec.akizukidenshi.com/catalog/g/gM-13337/
先ずは、こちら(↓)のサイトを参考にして壊れたPICkit3にFirmwareを書き込んでみました。
http://koibo.blog.fc2.com/blog-entry-40.html
PICkit4はPIC24FJ256GB106も(未だ殆どのデバイスが)βサポートなのですがMPLAB-X IDEで接続して、書き込むことが出来ました。
*****************************************************
Connecting to MPLAB PICkit 4...
Currently loaded versions:
Application version............00.02.00
Boot version...................01.00.00
Script version.................00.02.52
Script build number............66d22ca77a
Application build number.......0123456789
Connecting to MPLAB PICkit 4...
Currently loaded versions:
Boot version...................01.00.00
Updating firmware application...
Connecting to MPLAB PICkit 4...
Currently loaded versions:
Application version............00.03.09
Boot version...................01.00.00
Script version.................00.02.52
Script build number............66d22ca77a
Application build number.......0123456789
PICkit 4 is supplying power to the target (3.25 volts).
Target device PIC24FJ256GB106 found.
Device Id Revision = 0x3
Erasing...
The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x2ff
program memory: start address = 0x800, end address = 0x7fff
program memory: start address = 0xec00, end address = 0xedff
program memory: start address = 0xf000, end address = 0xf2ff
program memory: start address = 0xf800, end address = 0xf8ff
program memory: start address = 0x10000, end address = 0x15bff
program memory: start address = 0x29f00, end address = 0x29fff
configuration memory
Programming/Verify complete
*****************************************************
PICkit3のUSBケーブルを接続し直すとStatusの赤色LEDが消えて、直ったように見えたのですが・・・
Connection failed から抜け出すことは出来ませんでした。orz
もう一台のPICkit3にFirmwareを書き込む準備が出来たら、再挑戦します。
ーーーーーーーーーーーーーーーーーーーーーーー
<おまけの報告>
PICkit4はPIC16F1829もβサポートですがプログラムを書き込んでデバッグすることが出来ました。
(実はかなり使える?)
コメント 0